618-599-2748 or 815-739-8374

E2U Polyaspartic Skydrol Resistant 2 Gal

$237.60

E2U Polyaspartics is the next generation in two component, fast drying, Aliphatic Polyurea.

Clear
Questions about this product?
Description

Description

E2U Skydrol Polyaspartics is the next generation in two component, fast drying, Aliphatic Polyurea. It has excellent penetration and bond strength to surface. It features excellent abrasion and chemical, impact and wear resistant. It has cure time of four to six hours. It can be installed in extremely high or low temperatures. It is the ideal product when low odor, fast turnaround and a non-yellowing system are essential.

Physical Properties
Volumetric Ratio: . . . . . . . . . . . . . . . . 1 to 1
Volumetric Solids . . . . . . . . . . . . . . . .. 93%
Coverage: . . . . . . . . . . 200 SF/Gal @ 8 mil
Application temperature: . . . . .35-100°F
Thinning: . . . . . . . . . . . . . . . . .Not required
Pot life: . . . . . . . . . . . . . . . . . 15-20 minutes
Working time on floor: . . 15-20 minutes
Cure time: . . . . . . . . . . . . . . . . . . .4-6 hours
Critical recoat time: . . . . . . . . . . . 12 hours
Shelf life: . . . . . . . . . . . . . . . . . . . 12 months
USDA Food & Beverage:. . . . Meets Req.

Color: Clear
Available Colors:

Clear Beige
Light Gray Tile Red
Medium Gray Safety Red
Dark Gray Safety Blue
White Safety Green
Black Safety Yellow
Tan

Packaging
2 Gallon Kit:
PartA . . . . . . . . . . . . . . . . . . . . . . . . . . .1 gal.
Part B. . . . . . . . . . . . . . . . . . . . . . . . . . .1 gal.
10 Gallon Kit:
PartA . . . . . . . . . . . . . . . . . . . . . . . . . . .5 gal.
Part B. . . . . . . . . . . . . . . . . . . . . . . . . . .5 gal.

WARNING! SLIP AND FALL PRECAUTIONS
OSHA and the American Disabilities Act (ADA) have now set enforceable standards for slipresistance on pedestrian surfaces. The current coefficient of friction required by ADA is .6 on level surfaces and .8 on ramps. E2U Flooring recommends the use of angular slipresistant aggregate in all coatings or flooring systems that may be exposed to wet, oily or greasy conditions. It is the contractor and end users’ responsibility to provide a flooring system that meets current safety standards. E2U or its sales agents will not be responsible for injury incurred in a slip and fall accident.

WARRANTY
E2U products are warranted for one year after date of purchase. Please refer to the Limited Material warranty for additional clarification.

Handling Precautions
Use only with adequate ventilation. Appropriate cartridge-type respirator must be used during application in confined areas. Avoid contact with skin. Some individuals may be allergic to epoxy resin. Protective gloves and clothing are recommended.

Applications

Applications

Pharmaceutical Food Prep/Kitchens
Garage Floors Restrooms
Manufacturing plants Aisle ways
Clean rooms Auto showrooms
Schools Laboratories
Basements Kennels
Veterinary facilities Locker rooms
Ramps Health Care facilities
Loading docks Car wash facilities
Advantages

Advantages

Skydrol Resistant 4x more abrasion resistant than epoxy
Non-yellowing Chemically resistant
Low viscosity Easy mixing ration (1:1)
Solvent Free Cure at temperatures just above Freezing
High flowability
Typical Properties

Typical Properties

PROPERTY VALUE
Appearance Clear Liquid
Total Solids (% by Weight) 93
Total Solids (% by Volume) 93
Surface Tension, Dynes/cm 40
Viscosity (Brookfield LVF), cps @ 25° C 600
Density (lbs/gallon) 8.32
Specific Gravity 1.0
Flash Point (C Pensky-Martens closed cup) <70°F
Freeze/Thaw Stability N/A
Thermal Stability (28 days @ 52° C) No Effect
Mechanical Stability Good
VOC (g/l) 0
VOC (by Weight) 0
Tg (C) 66
Tensile Strength, psi 7000
Elongation 8%
Concrete Preparation

Concrete Preparation

Before coating is applied, concrete must be:
• Dry – No wet areas
• Clean – Contaminants removed
• Profiled – Surface etched
• Sound – All cracks and spalled areas repaired
Mechanical preparation is the preferred method of preparing concrete for coat- ing application. Shot-blasting, diamond grinding, scarifying and scabbling are all acceptable methods

Patching

Patching

Voids, cracks and imperfections will be seen in finished coating if the concrete is not patched correctly. Patch concrete with Easy Patch. After the patching material is cured, diamond grind patch. If a non-patching material is used, contact a technical representative for a compatible and approved alternative.

Testing

Testing

All surfaces are not the same. It is recommended that a sample area be done before the start of the project. The test should be done on-site, using the pro- posed method by the assigned applicator to insure proper adhesion and color. A sample area should also be done on any existing coatings to determine if any contaminants exist or if delaminating will occur.

Mixing

Mixing

The ratio of Polyaspartic 85 is 1 to 1. 1 part A (resin) to 1 part B (hardener). Generally, one mixed gallon is ideal for application. Mix the following with a stir stick. Note: If using a drill mixer, use a low speed to prevent air entrapment.
1. Pour out 1/2 gallon of Part A into a clean bucket.
2. Add 1/2 gallon of Part B and mix for 2 minutes.
**Do not store product in direct sunlight

Clean Up

Clean Up

While in an un-reacted state, may be cleaned up with water and degreaser. Isopropyl alcohol or acetone may be needed once the resin begins hardening. Lastly, a strong solvent like methylene chloride may be required if resin is nearly set up.

Film Properties

Film Properties

PHYSICAL PERFORMANCE PROPERTIES OF DRY FILM
All tests were conducted on 2.0 to 2.5 mil films, and air-dried for seven days at room temperature.

PROPERTY VALUE
Hardness (Pencil / Sword) 2H / 70
Taber Abrasion (mg loss per 1000 cycles, CS-17 wheel, 1000 load) 90
Impact Resistance (Direct / Reverse) 140 / 140 (lbs)
Crosshatch Adhesion (Untreated Cold Rolled Steel / Untreated Aluminum) 100% / 100%

QUV WEATHEROMETER (ALCLAD ALUMINUM 1000 HRS.)

PROPERTY VALUE
Oxidation No Effect
Loss of Gloss Slight

CHEMICAL RESISTANCE: 7-DAY SUBMERSION

PROPERTY VALUE
Brake Fluid No Effect
Transmission Fluid Slight Discoloration
Coolant No Effect
Power Steering Fluid Slight Discoloration
Battery Acid Damaged
MEK  <200 Double Rubs
Acetone  <200 Double Rubs
Formula 409  <200 Double Rubs
Datasheet